How often should you test a metal detector in food production? The answer depends on your facility's risk assessment, customer requirements, and ability to control product if the detector fails.
A reliable metal detector verification procedure does more than confirm that a machine sounds an alarm. It demonstrates that the detector identifies approved test pieces, rejects affected product correctly, and performs consistently during normal production.
This guide explains when to perform checks, how to position test pieces, what to do when a test fails, and which records to maintain. It also includes a free metal detector check log that your team can adapt to its approved procedures.
Monitoring vs. Verification vs. Validation: Understanding HACCP Terms
Although these terms are sometimes used interchangeably, they describe different food safety activities.
Monitoring involves scheduled observations or measurements used to determine whether a control is operating within established limits. Verification confirms that the food safety system and its procedures are being implemented and working as intended. Validation establishes evidence that a control measure is capable of controlling the identified hazard.
Routine metal detector challenge checks are commonly called verification tests. Where metal detection is designated as a critical control point (CCP), these checks may also form part of CCP monitoring. The exact classification should follow your facility's HACCP or food safety plan.
For this article, "detector checks" refers to routine performance tests using approved metal detector test pieces.
How Often Should You Test a Metal Detector in Food Production?
There is no single testing interval that applies to every food manufacturing operation. A facility should establish a documented, risk-based schedule that meets applicable certification, customer, and internal requirements.
A typical metal detector checking schedule includes the following events:
- Start-up: Before releasing product into normal production, confirm that the detector and rejection system function correctly.
- During production: Conduct checks at predetermined intervals established by the site's risk assessment.
- Product changeovers: Verify performance when switching products, recipes, packaging, or detector programs where the change may affect detection.
- After maintenance or adjustment: Test after repairs, sensitivity changes, equipment movement, or other work that could influence detector performance.
- After interruptions: Perform additional checks following relevant power interruptions, equipment faults, or extended stoppages.
- End of production: Complete a final check to confirm satisfactory operation at the end of the production period.
How Should You Set the Testing Interval?
The interval should account for the amount of potentially affected product your facility can identify, isolate, and hold if a test fails.
For example, a facility testing every two hours may need to assess up to two hours of production after an unsuccessful check. A shorter interval can reduce the amount of product requiring investigation, although the appropriate frequency must still be justified by risk.
Consider production volume, product risk, detector reliability, available traceability, customer requirements, and the practicality of segregating affected lots.
Example: A facility might establish checks at start-up, every hour, at changeovers, after relevant adjustments, and at the end of the run. This is an example schedule, not a universal requirement.
The documented frequency must be supported by the site's risk assessment and applicable standards.
Step-by-Step Metal Detector Verification Procedure
Use the following procedure as a framework for developing or reviewing your site's standard operating procedure (SOP). Always follow the equipment manufacturer's instructions and the facility's approved validation and verification requirements.
Step 1: Confirm the Detector Is Ready
Before testing, verify that the correct product program is selected, the equipment is operating normally, and the rejection system is available.
Confirm that the conveyor, reject mechanism, sensors, air supply where applicable, and reject container are in their required operating condition.
Step 2: Select the Approved Test Pieces
Obtain the approved ferrous (Fe), non-ferrous (NFe), and stainless steel (SS 316) standards specified in your procedure.
Each test piece should be clearly identified by contaminant type and sphere diameter.
Do not substitute a smaller or larger standard without authorization. The approved sizes should reflect the facility's established sensitivity requirements.
For guidance on selecting diameters, read Metal Detector Test Piece Sizes: Fe, NFe & Stainless Guide.
Step 3: Test With Representative Product
Where practical, place the test piece inside a clearly identified sample pack of the food currently being manufactured.
If insertion is not practical, use the validated alternative placement method specified by the detector manufacturer and site procedure.
Testing with actual product is important because moisture, salt, temperature, packaging, and other characteristics can influence detector performance.
Run the test at normal production speed, using the correct detector settings.
Step 4: Challenge the Required Positions
For conveyor metal detectors, the center of the aperture is often the least-sensitive location. The actual challenge position should be established using equipment guidance and validation.
Your procedure may also require the test piece to be positioned at the leading, middle, and trailing portions of the product or test pack.
- Leading edge: Test piece enters near the front of the product.
- Middle: Test piece is positioned around the product's center.
- Trailing edge: Test piece passes near the rear of the product.
These positions can help evaluate detection and rejection timing as the contaminated test pack moves through the system.
Do not assume that three positions are sufficient for every detector. Follow the approved challenge locations and orientations for your specific installation.
Step 5: Test Each Metal Type Separately
Pass the approved ferrous, non-ferrous, and stainless steel standards through the detector individually, following the established sequence.
For each test, confirm that the detector responds and that the correct test pack is rejected.
Where required, conduct successive test-pack challenges to verify that the detector and reject system continue functioning when products arrive close together.
Record a pass or fail for each metal type rather than recording only one overall result.
Step 6: Confirm Rejection and Record the Results
Observe the entire rejection event and confirm that the affected test pack is diverted or otherwise controlled correctly.
Complete the metal detector check log immediately, including the time, product, test piece sizes, results, reject confirmation, and operator initials.
Any unsuccessful check must trigger the facility's documented failure procedure.
Test the Reject System, Not Just the Alarm
A detector can identify metal and still fail to remove contaminated product from the production stream.
For example, the detector may produce an alarm while a faulty reject mechanism allows the affected package to continue down the conveyor.
That is why an effective verification procedure must confirm both detection and rejection.
For automatic reject systems, verify that the correct test pack enters the designated secure reject container. Where the facility uses a locked reject bin, confirm that it is properly secured and accessible only to authorized personnel.
For belt-stop systems, confirm that the conveyor stops and that the affected product can be identified and controlled.
Where installed, the procedure should also check relevant fail-safe functions, including:
- Reject confirmation sensors.
- Reject-bin-full detection.
- Low-air-pressure monitoring.
- Reject mechanism faults.
- Other fitted equipment interlocks or fault alarms.
These checks should follow the equipment manufacturer's recommended method. Never bypass a safety interlock or introduce an unsafe condition to perform a test.
The objective is to verify that contaminated product cannot pass through the system unnoticed when a relevant component fails.
What to Do When a Metal Detector Check Fails
A failed metal detector check must be treated as a potential loss of foreign material control.
The facility should have a written metal detector failed test procedure that employees understand before an incident occurs.
Step 1: Stop and Notify
Stop the affected production line or prevent further product release according to the site's procedure.
Notify the designated supervisor, quality assurance representative, or food safety manager immediately.
Step 2: Identify and Hold Affected Product
Identify all potentially affected product manufactured since the last satisfactory check.
Place that product on hold using the facility's traceability and inventory controls. Include relevant work-in-progress and finished goods that may already have moved downstream.
The scope of the hold should be based on the last demonstrated satisfactory operation and the investigation findings.
Step 3: Investigate the Cause
Determine whether the failure resulted from incorrect settings, product effect, a damaged test piece, detector malfunction, reject timing, air pressure, sensor failure, or another issue.
Do not simply repeat the test until it passes without investigating the original failure.
Step 4: Correct and Reverify
Have authorized personnel correct the problem. Then repeat the approved verification procedure, including all required metal types and reject checks.
Where the failure affects validated operating parameters, assess whether additional validation or technical review is required.
Step 5: Reinspect and Document Product Disposition
Reinspect affected product using a demonstrated effective inspection method, where appropriate, and follow the site's documented disposition procedure.
Quality assurance should authorize any release, rework, or disposal decision.
Record the failure, product quantities, root cause, corrective action, reinspection results, and final disposition.
Production should restart only after the equipment has passed the required checks and the authorized person approves the restart.
What Auditors Check: BRCGS Food Safety Issue 9, Clause 4.10.3
Facilities certified to BRCGS Global Standard Food Safety Issue 9 should pay particular attention to section 4.10, which addresses foreign-body detection and removal equipment.
Clause 4.10.3 covers metal detectors and X-ray equipment. Its requirements address documented operating and testing procedures, testing responsibilities, sensitivity, frequency, records, detection and rejection performance, and appropriate challenge standards.
Auditors may examine whether:
- The site has established and justified its testing frequency.
- Approved test pieces are correctly identified by material and diameter.
- Ferrous, non-ferrous, and stainless steel checks are performed as applicable.
- Testing reflects normal production conditions and required challenge positions.
- The reject mechanism and applicable fail-safe systems are checked.
- Operators follow the written procedure consistently.
- Records are complete, accurate, and reviewed as required.
- Failed checks trigger appropriate product isolation, investigation, and corrective action.
BRCGS Issue 9 also addresses the site's ability to identify, hold, and prevent release of potentially affected product if foreign-body detection equipment fails.
For audit preparation, compare your SOP and completed records against the applicable standard, equipment instructions, and customer specifications.
Reference: BRCGS Global Standard Food Safety, Issue 9, sections 4.10.1 and 4.10.3.
Download the Free Metal Detector Check Log
A consistent record makes it easier to demonstrate that checks were completed and that unsuccessful results received appropriate follow-up.
Blue Supply Company has prepared a printable metal detector check log template that includes:
- Date, time, production line, and product.
- Approved Fe, NFe, and SS 316 test piece sizes.
- Individual pass/fail results for each metal type.
- Reject confirmation and fail-safe check results.
- Operator initials.
- Corrective action and affected-product references.
- QA review and disposition information.
Visit the Documents Page to Download the Free Metal Detector Check Log
Publishing note: Upload the supplied PDF to the Documents page before advertising the download as available. Replace this link with the direct PDF URL when published.
For completing paper records in controlled production environments, explore Blue Supply Company's detectable pens and clipboards.
Frequently Asked Questions About Metal Detector Verification
How often should a metal detector be tested in food production?
Test at start-up, at documented intervals during production, after relevant changes or adjustments, and at the end of production. The exact frequency should be justified by risk, customer requirements, and the site's ability to control affected product after a failure.
Where should the test piece be placed?
For conveyor systems, challenge the established least-sensitive area, often near the center of the aperture. Use the required leading, middle, and trailing product positions where specified by the approved procedure.
What happens if a metal detector fails a test?
Stop or control affected production, notify QA, hold potentially affected product since the last satisfactory check, investigate the failure, restore equipment performance, and document product disposition before authorized restart.
Should you test with product or without?
Testing with representative product is generally preferred because product characteristics can affect detection. Use a clearly identified test pack where practical, or an approved alternative established through the equipment manufacturer's guidance and site procedure.
Who should perform metal detector checks?
Trained and authorized employees, such as QA technicians or designated line operators, should perform routine checks. The procedure should define who conducts tests, who reviews records, and who has authority to manage failures and approve restart.
Keep Your Metal Detector Verification Program Consistent
An effective metal detector verification procedure combines risk-based testing frequency, appropriate challenge standards, correct test placement, confirmed rejection, and documented corrective actions.
Using consistent methods and complete records helps food safety teams identify equipment problems promptly and demonstrate control during audits.
Blue Supply Company supplies metal detector test wands and test cards in multiple contaminant sizes and formats.
For more information, read How Metal Detection Test Pieces Verify Food Safety Systems and Building a Foreign Material Prevention Program for Food Manufacturing.
Need help selecting test standards for your inspection equipment? Contact Blue Supply Company at service@bluesupplycompany.com or call (888) 585-8725.
Blue Supply Company | Reliable Detectable Goods



